Lift a car is the most important and valuable part when you have to repair your vehicle. And for lifting, you need to gather jacking up tools like Jack stand floor Jack or hydraulic Jack. Learning how to jack up your car is not that difficult, you may think. It is a great helper and will make your car more stable.
However, a different car has different jacking points. But if you want to jack up your car from the front, you can do it straightforwardly.
Jacking up a car from the front is much easier than jacking from the other part. Your vehicle will smoothly go higher when you put a jack in the front. In this article, you will know some essential tips and steps about how to jack up a car from the front.
Types of Jack
- Hi-lift jack
- Hydraulic bottle jack
- Scissor jack
- Floor jack
Things you will Need
- Instruction manual
- A floor jack( or you can use any other)
- Wheel chocks, heavy piece of wood or cinder blocks to support your car and block the wheel
- A pair of jack stands
- Lug wrench
- Flashlight
- Safety precaution
A Process on How to Jack Up a Car from The Front
Here Is the process of jacking up the car from the front.
Step 1: Select a Proper Place to Park your Car
The first step is to select a secure surface for jacking up your car because the car can easily roll if you make any error. Do not keep your car on gravel or sand or any kind of loose surface; otherwise, the jacks will lose the ability to support your car.
So, you have to be careful about choosing the repair place. Concrete ground is the best place for parking your car.
Step 2: Secure Your Vehicle (Wheel Chocks)
Once you are done with parking your vehicle, put your car in a neutral position, and engage the parking brake. Also, check if there is engine oil on the tank. If there is enough engine oil, you should remove it before starting the procedure.
Moreover, sometimes excessive hydraulic fluid in the engine can create problems, so check it out. Properly reduce the level of hydraulic fluid as a part of securing a vehicle.
After that, put wheel chocks or a wood piece in front and backside of the wheel so that your car won’t move or roll while working. You have to follow this strictly if you are working under the car; otherwise, a big accident may happen.
Step 3: Locate the Jack Points on a Car
It is vital to find where to lift the vehicle or what jack points on a car are safe to lift the car because if you point the jack in the wrong place, your car may get serious damage and break any essential parts.
Locate if the area is secure enough and does not consist of different car components like ac compressor, batteries, oil tanks, etc.
Step 4: Where to Put Hydraulic Jack Under Car
And here comes the need of instruction manual. You will find a diagram there, or you can also search online for a better view.
Most of the modern car has the jacking spot right underneath the stabilizer bar when you have to lift your car from the front.
Step 5: Where to Put Jack Stands Under Car
Finding where to put jack stands under a car is really important to put it properly in the right area. Without it, you will need more pressure and energy to do the process. So, to do it smoothly, you should locate the right area.
Choose a lug jack or other appropriate jack that has proper padding on jack handle. It is not only for comfort but also for secure action for
Once you have located the jack points on a car, the next part is to put the floor jack under the proper spot. To prevent damage, you can set a piece of wood on the jack plate.
Step 6: Rise the Jack to Lift the Car
Using floor jack is more suitable for lifting your car. you need to close the release valve before using the floor jack. If you rotate the lever following the clockwise direction (relief valve), the job will be done correctly.
Also, do not forget to check the right and left-hand side position without the relief valve is adequately positioned.
They should be tightened and loosen on each side. Now raise the car by pumping the jack handle ups and down until the vehicle reached the desired height.
Remember, if you are going to remove your wheels, you should lose the lugs before using the jacks. Because losing the lugs from higher is painful than losing it from the ground.
Also, if you are a beginner, you should recheck the jacking position if it is set correctly.
Step 7: How Do You Jack Up a Car high With Jack
While raising the car, check the movement if it is appropriately lifting and if it is stable enough. After lifting the vehicle, do not go underneath the car before placing the jack stand. Put the jack stand in the pinch welded area.
Check out different areas like oil tank, suspension components, a level ground of oil tank, front and rear loosen up parts, etc. Diagnosis of the vehicle before lifting it up.
Step 8: Check the Stability
When the lifting job is done, check if the vehicle is stable enough to work comfortably. If you have to work for a long time like removing a wheel, use extra jack stands for better support.
Make sure the height is appropriate for the jack stands when you are lifting the car with a floor jack. Put the extra jack near the working area to make better support, and you will get enough space to work.
Step 8: Lower the Car Back
After finish, your work, remove the jack stands and lower the vehicle. But before that, tighten the lugs of wheel and recheck all the sections where you are worked.
After that, open the release valve following a counterclockwise way. You should follow those steps in every type of jack. Remove the jack stands and slowly lower down the car on the ground.
The process is similar to the questions like how to jack up a car all four wheels, how to jack up a car each wheel, etc.
How to Lift a Car without Jack
A typical situation every car owner would face is forgetting to take jack with them. Just imagine what you will do if your car gets a problem in the middle of the street, and you do not have a jack to lift? To prevent this kind of situation, follow the below steps correctly.
The first thing you need to do is jack up from the front. So place chocks or any wood and engage the emergency brake. Now, in this case, you will need a helping hand for lifting, and any knowledge about the car is not required.
Park your car at an angle so one of the wheels will be up and the other is don’t. Also, you can drive your jeep/other vehicles on a curb so that you will get enough space for working under the car. If you have to lift your truck higher, place the whole vehicle on the curb.
Where to Put Jack Stands Under the Car
It is essential to know where to put the jack stands because the points are susceptible, and if you put the positions in the wrong place, your car may get damaged severely. To avoid thins, you should clearly know the location of the jacking.
Every jeep or other 4wheelers has its instruction manual where the jacking points are being shown. So read the manual before using the stands and follow the steps correctly. However, different vehicles have different jacking points.
You will find a couple of different options. The first is the tow hooks. It is located right underneath the engine section. If your car goes to a ditch, the area is made to support the vehicle.
In this area, you can find four jack standpoints too. Also, there is a stabilizer bar attached to the body. This might be another right choice for pointing jack because these are often reinforced areas of the vehicle.
Next place is right with the control arm. That lower control arm comes with the body of the vehicle. This area is also made to support the weight. But this place is curved and as the suspension compresses. So when you lift, it may tend to slide off. So it will be better if you avoid those areas.
Do not jack up underneath the oil pan; otherwise, it may cause damage to the engine.
Leave a Reply